CertainTeed Gutter Replacement Nationwide

CertainTeed Gutter Replacement: The Fort Worth Owner’s Guide

If your CertainTeed gutters are pulling away from the fascia, leaking at the seams, or sagging between hangers, we can replace them with CertainTeed-compatible materials and have the job done right. Most Fort Worth gutter replacement jobs run $850 to $1,900 installed for a typical single-story home, depending on linear footage, accessibility, and whether we’re replacing downspouts too. You’ll usually notice the problem after a hard rain, when water pours over the edge in one spot instead of flowing to the downspout, or when you spot rust streaks on the gutter face and a section that’s tilted a few degrees off level.

Call (682) 730-3548

We’re Crestview Roofing Co Fort Worth, and we’re an independent service provider, not affiliated with CertainTeed. That means we can source the right materials without markup games, and we tell you exactly what you’re paying for. Dylan Pace and our crew have replaced gutters on homes across Fort Worth, from Ryan Place to Benbrook to the neighborhoods off Camp Bowie, and the failure patterns are consistent: Texas sun bakes the sealant, hail dents the aluminum, and the freeze-thaw cycle slowly separates the seams until one good storm makes the damage obvious.

Which CertainTeed Models This Applies To

CertainTeed manufactures gutters through its parent company’s building products division, and the two lines we see most often in Fort Worth are the 5-inch and 6-inch seamless aluminum systems, typically installed in the HX® K-style profile. The HX designation refers to the heavier gauge aluminum, usually .027 or .032 thickness, versus the lighter .024 you’ll find on builder-grade jobs. If you have CertainTeed gutters, check the end cap or a downspout bracket for a small stamped “CT” or “CertainTeed” mark. If that’s worn off, measure the top opening: 5 inches means you have the standard residential profile, 6 inches means someone upsized for heavier Fort Worth rainfall and steep roof pitch.

Here’s the compatibility gotcha: CertainTeed’s 5-inch and 6-inch systems use different hanger spacing than a lot of aftermarket parts. The factory spec is often 2 feet on center, but Texas code allows up to 30 inches. If a previous installer stretched hanger spacing to save money, the gutters will sag even with a new section installed, because the hangers are doing more work than they were rated for. We always check and correct hanger spacing when we replace a section, and we match OEM or heavy-gauge equivalents. For most Fort Worth homes, a quality aftermarket .032 aluminum section performs as well as the CertainTeed-branded part and costs roughly 15-20% less, which is savings we pass on in writing.

Signs Your CertainTeed Gutter Replacement Is Failing

• Water overflowing at one specific point. This usually means a seam has separated or the section is pitched the wrong direction. The gutter can’t carry water it can’t hold, and you’ll see a clean spot in the mulch or mud below where the water hits hard.
• Sagging between hangers. Aluminum expands and contracts with Texas heat, and over time that movement loosens hangers. A gutter that drops an inch over 8 feet is redirecting water away from the downspout and pulling the fascia away from the home.
• Rust streaks or small holes near the end caps. Standing water is the enemy. When a section loses its pitch, water pools and sits, and Fort Worth’s hard water accelerates corrosion on any surface scratch.
• Gutter pulling away from the roofline. The fascia board behind the gutter is likely soft or rotting, which happens when overflow has been running behind the gutter for a season. You can’t fix this with a new gutter section alone; you need to repair the fascia too. We see this on older homes in the Ridglea Hills and Wedgwood areas where homeowners didn’t catch the overflow early.
• Downspout disconnected or cracked at the elbow. The downspout takes the most abuse from ladder bumps, mower hits, and kids. A cracked downspout section hydraulically traps water and causes the gutter above it to back up.

Replacement Cost & What’s Included

In Fort Worth, a straightforward CertainTeed-compatible gutter replacement on a single-story home runs $850 to $1,900 installed. A partial section repair, if the rest of the run is sound, is often $250 to $550. Two-story homes push toward the top of the range, and steel or copper upgrades are more. The two biggest drivers are linear footage and whether the wood fascia behind the gutter is sound. If the fascia is rotted, we’ll tell you before we quote, and that’s a separate repair.

Every quote is a written, line-item price before any work starts. That’s how The Relay Visibility Guarantee works, and it’s the same standard we’ve held since 2000. The number you approve is the number you pay. Every gutter replacement carries the 365-Day Done Right Promise: if it fails within a year of install, we come back and fix it at no charge. In writing, included with every job.

DIY or Call Us?

You can safely check your gutters from the ground with a pair of binoculars: look for sagging, peeling sealant at the seams, and visible rust near the end caps. A level held against the bottom of the gutter from a stepladder will tell you whether the pitch is still working. What you shouldn’t do is lean a ladder against a gutter that’s already pulling away, because the gutter will flex and the ladder can slide sideways. Gutter work at height accounts for thousands of ER visits every year, and a fall from a two-story eave in Fort Worth is a life-changing injury, not a scrape.

The honest answer is that gutter replacement is not the hardest trade, but it is the kind of job where one wrong hanger placement means the whole run fails again in six months. We know the specific hanger spacing CertainTeed systems need, we correct pitch, and we document everything with before-and-after photos. If you’re even mildly unsure, call us at (682) 730-3548 and we’ll give you a straight answer and a written quote. Put it in writing or don’t bother saying it.

FAQs