Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Gutter Replacement: The Fort Worth Owner’s Guide
Boral gutter replacement in Fort Worth typically runs $14 – $28 per linear foot installed, with most single-story homes landing between $650 and $1,400 for a complete gutter run. We stock Boral-compatible aluminum and steel gutter sections, downspouts, elbows, and hangers on our trucks, so most replacements are done in a single visit. Homeowners usually discover the problem the same way every time: after a hard Fort Worth storm, water pours over the gutter like a waterfall instead of running through the downspout, or a section has pulled loose and is hanging by a single bracket.
Boral gutters are tough, but they’re not indestructible. The Texas sun bakes the sealant at the seams, hail dents the aluminum, and the clay-heavy soil around Fort Worth shifts enough to pull hangers loose over time. When a section fails, replacing it right keeps water off your fascia boards and away from your foundation. Water against a foundation in this part of Texas is how you get cracked brick and a $9,000 repair bill. We’d rather swap a gutter.
One thing to know up front: Crestview Roofing Co Fort Worth is an independent service provider. We’re not affiliated with Boral, but we install and repair using Boral-compatible materials and have years of hands-on experience matching their profiles, gauges, and mounting systems.
Which Boral Models This Applies To
Boral manufactures gutter systems in two primary lines for the U.S. market: the Boral Steel Gutter System and the Boral Aluminum Gutter System. Both use a K-style profile, which means the face of the gutter has a stepped, ogee curve, not a half-round bowl. If your home has the Boral Steel system, you’re dealing with a heavier gauge material that holds up better to hail but costs more to replace section-for-section. The Aluminum system is lighter and what we see more often on Fort Worth homes built in the last 15 years.
Identifying your Boral gutter is straightforward. Look inside the gutter on a dry day. Boral stamps their name and gauge number on the interior face of the channel, usually every 4 to 6 feet. If the stamp has worn off, measure the gutter width: 5-inch K-style is standard for most residential, while 6-inch is common on larger roof planes or homes with tile roofing like the Boral concrete and clay tile systems we install.
Here’s the compatibility gotcha that catches a lot of homeowners: Boral’s downspout dimensions do not always match the generic 2×3 or 3×4 downspouts sold at big-box stores. Their older steel line used a 2.5×3.5 downspout that’s now hard to find off the shelf. We fabricate or order the correct sizing rather than forcing an undersized downspout onto the outlet, which creates clogs and overflow. It’s one of those details that makes the difference between a gutter that works for 20 years and one that backs up every fall when the live oaks drop their leaves over in Ryan Place.
When it comes to OEM versus aftermarket, for Boral gutters specifically, we prefer OEM-matched aluminum sections where the profile needs to line up perfectly. A slightly off profile looks wrong from the street and leaves a visible seam. For hangers, brackets, and hidden fasteners, a quality aftermarket equivalent rated for the same gauge material works fine and costs less without a durability hit.
Styles & brands we work with
Signs Your Boral Gutter Replacement Is Failing
- Water spilling over the front edge during normal rain. This usually means a seam has separated or the gutter has lost pitch. In Fort Worth’s clay soil, the fascia line settles unevenly over time, and a gutter that was pitched correctly at install can end up holding water in the middle.
- Gutter pulling away from the fascia board. The lag screws or hidden hangers have worked loose from the wood. We see this regularly after drought summers when the fascia dries out and the wood around the fastener shrinks.
- Visible rust at the end caps or outlet. Boral steel gutters will eventually rust at the seams where the protective coating got scratched during install or by hail. A rusted end cap is a simple fix; a rusted-through channel means section replacement.
- Sagging in the middle of a run. This points to hanger spacing that’s too wide or hanger failure. Boral’s specs call for hangers every 24 inches, and when a previous installer stretched that to 32 inches to save a few bucks, gravity eventually wins.
- Water staining on the fascia board directly behind the gutter. That tells you water has been escaping behind the gutter, not over the front. The drip edge wasn’t seated into the gutter channel properly. If left alone, the fascia starts to rot, and now you’re replacing wood along with the gutter.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a typical Fort Worth single-story home, a Boral gutter section replacement runs $180 to $340 per 20- to 30-foot run, which includes the material, removal of the failed section, installation, re-pitching, and sealant at the seams. A full gutter replacement on an average 1,800-square-foot home lands between $900 and $1,800 depending on linear footage, Gauge thickness, Steel versus aluminum, and how much downspout rework is needed.
| Item | Typical Fort Worth Range |
|---|---|
| Single section replacement (20 – 30 ft) | $180 – $340 |
| End cap or outlet replacement | $75 – $140 |
| Downspout replacement (2-story run) | $160 – $310 |
| Full gutter replacement (1,800 sq ft home) | $900 – $1,800 |
| Hanger replacement and re-pitch | $8 – $14 per hanger |
Every Boral gutter replacement we do includes the same written price before any work starts. The number on your quote is the number on your invoice. That comes from The Relay Visibility Guarantee, and it applies to every job we take in Fort Worth. You’ll also get a 365-Day Done Right Promise on the repair: if the gutter fails within a year, we come back and make it right at no charge. Put it in writing or don’t bother saying it. That’s how we operate.
DIY or Call Us?
You can safely identify what’s wrong with your Boral gutters by walking the perimeter on a dry day and looking for the signs we listed above. You can measure your gutter width and check the interior stamp to confirm the Boral profile. What we don’t recommend is pulling down a failed gutter section on a ladder yourself. Gutters are long and awkward, and a 20-foot section of aluminum or steel coming off its hangers can swing unpredictably. Falls from ladders are one of the most common home injuries in Tarrant County, and the gutters don’t need to be over your roof pitch to hurt you.
If the problem is a loose hanger or a small gap at a seam, popping a hanger back in or applying a quality gutter sealant is within reach for most homeowners who are comfortable on a ladder. If the section is dented beyond shape, rusted through, or pulling the fascia board loose with it, call us at (682) 730-3548. The replacement itself is quick, and we’ll match the Boral profile so the repair is invisible from the street.
FAQs
Boral aluminum gutters in the Fort Worth climate typically last 20 to 25 years, while their steel line can run 25 to 30 years if the coating stays intact. The main lifespan killers here are hail dents that trap water, UV degradation on sealant at the seams, and soil movement that throws off the gutter pitch. A gutter losing pitch almost always fails at a seam before the metal itself gives out. If your Boral gutters are past 20 years and you’re patching seams every spring, replacing the whole run often costs less than piecemeal repairs over another five years. Call (682) 730-3548 and we’ll give you an honest assessment.
Yes, if the damage is limited to a seam separation, a pulled hanger, a rusted end cap, or a small dent that doesn’t compromise the channel flow. We repair those issues routinely, seal the seam, re-secure the hanger, and you’re done. If the metal is creased badly enough to change the gutter profile, or rust has eaten through the channel, replacement is the cheaper long-term option because patching a creased section never seals right. We’ll tell you which one you need after looking, not before. Estimates are free.
A single-section replacement on a Boral gutter system takes 1 to 2 hours on site. A full overhaul including downspouts on an average Fort Worth home is usually done in half a day. Faster than most people expect, because we show up with the material already sized to your measurements and we don’t leave to run for parts mid-job. Call (682) 730-3548 and we’ll schedule a time that fits your day, not a four-hour window.
Yes. Our trucks carry 5-inch and 6-inch K-style aluminum sections, Boral-compatible downspout profiles in the older steel dimensions, end caps, outlets, hidden hangers, and sealant rated for the Fort Worth heat. We also keep materials for other major brands we service, including GAF, Owens Corning, and CertainTeed. When a section replacement is called in, we arrive with the right profile already on the truck, so the job doesn’t stretch across two visits.
We match the factory color as closely as the current Boral color chart allows. If your existing gutters are heavily faded from Texas sun, a brand-new section may look slightly darker at the seam for the first season until it weathers in. We’ll show you a physical color sample before we install anything, and if an exact match isn’t available, we’ll tell you before ordering so there are no surprises when you see it from the curb. Call (682) 730-3548 for a free estimate.
Written by Dylan Pace, Owner, Crestview Roofing Co Fort Worth at Crestview Roofing Co Fort Worth, serving Fort Worth and nearby areas.