Boral Shingle Repair Nationwide

Boral Shingle Repair: The Fort Worth Owner’s Guide

Boral shingle repair in Fort Worth typically runs $325 to $1,100 installed, depending on how many shingles failed and what’s underneath them. We stock Boral-compatible replacement shingles, color-match what’s on your roof now, and can usually complete a standard repair in one visit. Most Fort Worth homeowners notice the problem after a heavy spring storm loosens a few shingles, or when a leak shows up on the ceiling below a section of roof they haven’t thought about since the home was built.

Call (682) 730-3548

Here’s the honest truth about Boral: it’s a premium composite stone-coated steel product. It’s tough stuff. But when it fails, it rarely fails alone. Usually there’s a flashing issue, a fastening problem from the original install, or impact damage from hail that compromised the protective coating. That’s why we approach every Boral repair as a diagnosis, not just a patch job.

Which Boral Models This Applies To

Boral’s current stone-coated steel roofing in Fort Worth falls under the Boral Steel product line, which replaced the older Decra and Gerard lines that many local homes still have. The repair approach is the same across all three generationally different products, but matching is different. Older Decra shingles have a slightly different profile depth and color shading than today’s Boral Steel. If your roof was installed before 2015, you likely have Decra or Gerard; after 2015, it’s Boral Steel.

The compatibility gotcha most Fort Worth owners hit: Boral’s accessory parts, flashing pieces, battens, and underlayment have changed subtly over the years. A replacement shingle from today’s inventory may not interlock perfectly with shingles installed in 2012 without a small adjustment to the fastening pattern. We carry both current Boral Steel components and correctly-spec aftermarket equivalents machined to older Decra and Gerard profiles, so your repair doesn’t just match the color, it seats properly.

Boral doesn’t sell direct to homeowners, and their distribution network is selective. We buy through authorized channels and also work with quality aftermarket suppliers for discontinued profiles and colors. If we can’t source an exact Boral part for your older roof, we’ll tell you that in writing before any work starts, along with our recommendation for the closest functional match.

Signs Your Boral Shingle Repair Is Failing

• Interlocking tabs that don’t sit flat. Stone-coated steel shingles rely on a tight mechanical interlock. When the fasteners loosen or the underlayment shifts, the tabs rise slightly. You’ll see it as an uneven shadow line across a section of the roof. Left alone, water gets driven under the shingle by wind.
• Rust blooms or coating wear at the fastening points. Boral’s stone coating protects the steel core. When a screw head gets exposed, it rusts first. A rust streak running down from a shingle edge tells you moisture is getting where it shouldn’t.
• Granule-like stone loss in concentrated areas. Boral’s stone coating shouldn’t shed like asphalt. If you’re finding small granules in your gutters year after year and your roof is Boral, you’re looking at mechanical damage – usually from foot traffic or hail impact – not normal wear.
• Leaks at penetrations, not in the open field. Most Boral leaks happen where the roof meets a chimney, vent pipe, or wall. The shingle itself rarely fails mid-field; the flashing around the penetration does. That’s the first place we check on every Boral repair call in Fort Worth.
• Visible gaps or lifted edges after a storm. Texas wind doesn’t mess around. If you can see daylight under the edge of any shingle from the ground, it’s already loose enough for water to get driven underneath during the next rain.

Replacement Cost & What’s Included

Here are real Fort Worth numbers, not national averages. A single Boral shingle replacement, where we’re swapping one damaged shingle and using existing flashing, runs $325 to $550. A repair involving multiple shingles plus flashing work around a penetration, most common around chimneys and vent pipes in Fort Worth homes, runs $550 to $1,100. Full section repairs, where hail has damaged a contiguous area of Boral, can push higher, and we’ll give you a written price before any work starts.

Every Boral repair from Crestview Roofing includes the 365-Day Done Right Promise: if that repair fails within one year, we come back and fix it at no charge. No prorating, no negotiation. You also get a written price before work begins, before-and-after photos, and a digital invoice sent by text. The number on the page is the number on the invoice.

DIY or Call Us?

You can safely check a few things yourself: look for lifted edges from the ground, check gutters for stone granules, and inspect the ceiling below your roof for water staining after a storm. What we don’t recommend, even to capable DIYers, is walking a Boral roof. The stone coating is slippery when it’s worn, the metal edges are sharp, and the fastening system is specific to the product series. We regularly fix repairs where a well-meaning homeowner installed the wrong fastener and voided what was left of the original manufacturer coverage. One quick check from the ground is smart. Getting on a metal roof without knowing the fastening spec is not.

Dylan Pace has spent years putting roofs on Fort Worth homes, including a run of re-roofs near the Cultural District he’s still proud of. When we walk onto your property, we already know what to look for on a Boral roof. Call (682) 730-3548 and we’ll get you on the schedule. Like Dylan says: “Put it in writing or don’t bother saying it.”

FAQs