Tamko Gutter Replacement Nationwide

Tamko Gutter Replacement: The Fort Worth Owner’s Guide

Tamko gutter replacement in Fort Worth typically runs $14 to $28 per linear foot installed, which means a standard single-story home with about 160 linear feet of gutters lands between $2,240 and $4,480. We stock Tamko-compatible aluminum gutter systems on our trucks for most Fort Worth jobs, and a full replacement on an average ranch-style home takes one day. Most homeowners discover they need this work after a spring hailstorm punches through a section of gutter, or when a joint separates and water starts pouring over the fascia board during a Texas downpour.

Call (682) 730-3548

The gutters themselves rarely fail silently. You’ll see it: water spilling over the edge in one spot, a visible sag between hangers, or a seam that’s pulled apart after years of Fort Worth heat expanding and contracting the aluminum. The good news is that Tamko’s gutter profiles are standardized, which means matching replacements doesn’t require guesswork. We measure, match, and swap. That’s the whole job.

Which Tamko Models This Applies To

Tamko’s gutter product line covers the two profiles you’ll find on most Fort Worth homes: the standard 5-inch K-style gutter and the larger 6-inch half-round used on higher-pitch roofs or homes with substantial tree cover. The K-style is by far the more common on newer construction. It’s the one with the flat back and decorative front that mimics crown molding. If you look at the gutter from the ground and the front face has two distinct bends, you’re looking at K-style.

Here’s the compatibility detail most homeowners miss: Tamko K-style gutters use a standardized 5-inch profile, which means gutters from other major manufacturers will physically interlock with Tamko sections. The mounting brackets are the variable. Tamko’s hidden hanger spacing spec is 24 inches on center, and that spacing matters more than the brand stamped on the gutter. When we replace a section, we match the hanger style and spacing so the new gutter seats flush with what remains. You don’t need to replace the whole run just because one 10-foot section got crushed by a fallen limb.

OEM Tamko gutters and quality aftermarket equivalents like those from GAF or Owens Corning all use the same aluminum gauge range: 0.027 inches for standard residential, 0.032 for heavy-duty. In Fort Worth, where hail is a regular visitor, we recommend the heavier gauge on any roofline that faces the prevailing storm track. It costs about $3 more per linear foot and buys real dent resistance. Crestview Roofing Co Fort Worth is an independent service provider and not affiliated with Tamko, which means we stock what performs best for your specific roofline, not what a distributor pushes.

Signs Your Tamko Gutter Replacement Is Failing

• Water spilling over the front lip during normal rain. This usually means the gutter pitch has flattened over time. Aluminum expands and contracts with Fort Worth’s temperature swings, and hangers can loosen from the fascia. The water finds the low spot and pours over instead of flowing to the downspout.
• Visible sag or a gap between gutter and fascia board. When hangers pull loose, the gutter starts leaning away from the house. You’ll see daylight between the back of the gutter and the fascia. Left alone, water runs behind the gutter and rots the wood it’s mounted to.
• Separated seams at corners or mid-run joints. Tamko gutters are joined with sealant and hidden connectors. That sealant has a real lifespan of about 7 to 10 years in Texas heat before it dries out and cracks. A separated seam drips constantly, even days after the last rain.
• Rust streaks or pinhole leaks on the bottom of the gutter. Standing water accelerates oxidation. If leaves have been damming a section for a season or two, the trapped moisture eats through from the inside. By the time you see rust on the outside, the metal is paper-thin.
• Downspout pulling away from the wall. A downspout that’s started to lean or detach from its brackets is telling you the whole gutter run has shifted. The downspout is just the most visible part of a system that’s moving as a unit.

Replacement Cost & What’s Included

Here’s the honest math for Fort Worth. Standard 5-inch K-style aluminum gutter replacement runs $14 to $18 per linear foot installed, including removal of the old sections, new hangers, and seam sealing. Heavy-gauge 0.032-inch aluminum or 6-inch half-round runs $18 to $28 per linear foot. A straight two-story wall adds a couple dollars per foot because of the ladder and safety setup involved.

Every quote you get from us is written, line-itemed, and in your hands before any work starts. The number on the page is the number on the invoice. That’s The Relay Visibility Guarantee, and it applies to every job we do in Fort Worth. The installation itself includes new hidden hangers at spec spacing, sealed end caps, and a workmanship warranty that covers the replacement for 365 days under our Done Right Promise. If a seam we sealed fails within a year, we come back and fix it at no charge. No negotiation. No runaround.

DIY or Call Us?

Let’s be straight about what’s safe and what isn’t. Cleaning your gutters, checking hanger spacing with a tape measure from the ground, and spotting visible damage are all things a homeowner can and should do. If you want to mark a sagging section with a piece of tape so you can track whether it’s getting worse, go for it. That’s useful information when you call us.

Replacing a gutter section means working from a ladder at roofline height, handling 10-foot sections of aluminum in the wind, and getting the pitch right so water actually flows. The danger isn’t just falling. A poorly pitched replacement section creates a new low spot, which means the problem moves instead of getting fixed. If you’re comfortable on a ladder and have done this before, you already know what’s involved. If you’re not, call (682) 730-3548 and we’ll handle it same-week with a written price before we touch anything.

FAQs