Roof Installation in Fort Worth - Free Roof Inspection, Written Price

Trusted Roof Installation for Fort Worth Homeowners

A new roof in Fort Worth should last decades, not become a source of regret. Most full replacements we handle run from $11,500 to $19,800 for architectural shingles on a standard 1,800 to 2,600 square foot home, though asphalt 3-tab runs closer to $8,200 to $13,400. Standing seam metal typically lands between $18,900 and $34,700, while tile starts around $21,000 and can reach $38,600 for high-profile concrete or clay. Every number we give is written on paper before the first shingle comes off. That’s how Crestview Roofing Co Fort Worth has worked since 2000, and Dylan Pace, our owner, has never changed that rule. If you want a roofer who shows up with a real name, a real arrival time you can track, and a price that doesn’t move, call (682) 730-3548. We’re the Fort Worth Roof Installation team that puts the whole job in writing.

Call (682) 730-3548

Shingle Roof

A shingle roof is a roof covered in overlapping asphalt or composite shingles, the most common roofing system in Tarrant County because it handles hail season well, costs less upfront, and takes a crew only one to two days to install on most Roof Installation in Keller area homes. We install architectural and 3-tab shingle roofs using material from GAF, CertainTeed, and Owens Corning, and the typical full replacement in Fort Worth runs $8,200 to $19,800 depending on square footage, pitch, and how many layers we’re tearing off. A written price is delivered before any work starts, and the number on that page is the number on the invoice. Call (682) 730-3548 to schedule a free estimate for your shingle roof.

Architectural vs. 3-Tab

Architectural shingles are thicker, hold up better against Fort Worth hail, and carry longer manufacturer warranties, typically 30 years to lifetime. 3-tab shingles are lighter and cheaper but more vulnerable to wind lift on the open plains west of Loop 820. We’ll show you samples and prices for both before you commit to anything.

Tear-Off vs. Overlay

Some contractors will shingle over an old layer to save a day and a few hundred dollars. We almost always recommend a full tear-off because it lets us inspect the decking underneath, replace any rotted plywood, and install fresh underlayment. The cheap route hides problems; the right route finds them before they cost you a ceiling.

Standing Seam Metal Roof

A standing seam metal roof is a metal roofing system with vertical panels joined by raised seams that run from ridge to eave, and it’s the best option in Fort Worth if you want a roof that shrugs off hail, sheds heat, and lasts 40 to 60 years. We install 24-gauge and 26-gauge standing seam panels with concealed fasteners, and a full replacement on a typical Fort Worth home usually runs $18,900 to $34,700. It’s a bigger upfront investment than shingle, but the numbers work out for homeowners who plan to stay in the house. Call (682) 730-3548 and we’ll give you a written price before you spend a dollar.

Hail and Wind Performance

Fort Worth sits in a hail corridor, and standing seam metal has a Class 4 impact rating with most manufacturers, which means it withstands the kind of storm that totals a shingle roof. Insurance companies notice that, and many homeowners see a premium reduction after switching. The seams themselves are raised above the flat panel, so wind-driven rain can’t work its way into the fastener points.

Energy and Heat Reflection

Dark shingles absorb Texas sun and push heat into your attic. Standing seam panels, especially in lighter colors or with reflective coatings, bounce a good share of that heat back. In Fort Worth summers where the attic hits 140 degrees, that difference shows up on your electric bill every month from June through September.

Tile Roof

A tile roof is a roof finished with concrete or clay tiles, and in Fort Worth it’s the choice for homeowners who want the Spanish or Mediterranean look with a lifespan that can hit 50 to 75 years. We install concrete and clay tile systems, including the underlayment rebuild those roofs require, and a full tile roof in Fort Worth generally runs $21,000 to $38,600 depending on tile profile and roof complexity. Tile is heavy, so the first thing we do is verify your decking and framing can carry the load. Call (682) 730-3548 for an honest assessment and a written quote.

Weight and Structure

Clay tile weighs roughly 600 to 1,100 pounds per square, compared to about 230 to 300 for asphalt shingle. That means a tile roof isn’t a swap, it’s a structural project. We check truss spacing, deck thickness, and existing load paths before recommending tile so you don’t end up with sagging rafters in ten years.

Underlayment Is the Real Roof

The tile sheds water, but the underlayment below it is what keeps your home dry. In Fort Worth, where freeze-thaw cycles and hail are common, we install double-layer synthetic underlayment rated for high heat. A tile roof is only as good as what’s underneath, and we don’t cut that corner.

Roof Ventilation

Roof ventilation is the system of intake and exhaust vents that moves hot, moist air out of your attic so it doesn’t cook your shingles, rot your decking, or spike your cooling bill. In Fort Worth, a properly ventilated attic should run within about 10 to 15 degrees of the outside temperature, and on homes where it doesn’t, we add intake vents at the soffit and exhaust vents at the ridge to fix it. Ventilation work during a roof installation typically runs $350 to $1,200 depending on how much airflow your attic needs to meet building code. Call (682) 730-3548 and we’ll measure your attic’s actual airflow before recommending anything.

Intake and Exhaust Balance

Good ventilation needs roughly equal intake and exhaust. If your ridge vent is starved for air because your soffits are painted over or blocked, it creates negative pressure that pulls conditioned air out of your living space. We calculate the square footage of net free vent area your attic needs, then match intake and exhaust so the system actually moves air.

Fort Worth Heat and Shingle Life

An attic that hits 150 degrees in August bakes shingles from below and shortens their life by years. Proper roof ventilation drops that temperature, slows shingle aging, and reduces the load on your air conditioner. It’s a few hundred dollars of materials and labor that protects a twenty-thousand-dollar roof.

Roof Flashing Installation

Roof flashing installation is the process of installing metal strips that seal the joints where the roof meets a chimney, wall, skylight, or valley, and it’s the most common point of failure in any Fort Worth roofing system. We install and replace flashing using galvanized steel, aluminum, and copper, with a typical flashing job on a Fort Worth home running $450 to $1,900 depending on how many penetrations and transitions your roof has. Flashing is where most leaks start, not the shingles. Call (682) 730-3548 if you’re seeing water stains below a chimney or along an exterior wall.

Chimneys and Skylights

A chimney is a hole in your roof with bricks sticking out of it, and the flashing around it has to handle water flow, thermal expansion, and freeze-thaw cycles in Fort Worth winters. We install step flashing cut into the mortar joints, then counter-flashing over that, so water gets redirected down the roof instead of behind the brick. Skylights get a similar treatment with the manufacturer’s flashing kit plus a redundant layer of our own.

Valleys and Wall Junctions

Where two roof planes meet, water concentrates. In a valley, we install open metal valley flashing for homes with heavy tree debris, or closed cut shingles when the slope is steep enough. At wall junctions, we use step flashing behind the siding and house wrap. If your existing flashing is rusted through, we replace it before it becomes a ceiling stain.

TPO Roofing Installation

TPO roofing installation is the process of installing a white, single-ply thermoplastic membrane, and in Fort Worth it’s the standard choice for flat and low-slope commercial roofs because it reflects heat and welds into a watertight sheet. We install TPO in 45-mil, 60-mil, and 80-mil thicknesses, with a typical Fort Worth flat roof project running $5,800 to $12,400 depending on square footage and whether we’re doing a full tear-off or a recover. The heat-welded seams are actually stronger than the membrane itself. Call (682) 730-3548 if you have a flat roof that’s been patched one too many times.

Heat-Welded Seams

TPO seams are welded with hot air, not glued, which creates a chemical bond that water can’t get through. That’s the opposite of older torch-down systems where seams were the weak point. We weld every seam, then probe them with a seam tester to verify the bond before we call the job done.

Reflective Surface and Energy Load

White TPO reflects the majority of solar heat, which matters on a commercial or residential flat roof in Fort Worth where the sun hits that surface directly all day. The reduced heat load means a cooler building and less strain on your HVAC. For homeowners with flat-roof additions or garages, TPO is usually the smartest material choice.

Brands We Service

We install GAF shingles on the majority of our Fort Worth roofs, and we’ve built a relationship with their local territory manager that gets us direct answers on warranty claims. GAF’s Timberline HDZ line is our most common recommendation for architectural shingle roofs, and we’re certified to offer their extended warranty coverage.

CertainTeed and Owens Corning are the other two brands we install regularly, and each has a specific place. CertainTeed’s Landmark line is a great value for homeowners who want a step up in quality without a big price jump. Owens Corning’s Duration shingles are our go-to when a homeowner wants the strongest wind warranty on the market. Whether you have GAF, CertainTeed, Owens Corning, or any of the other major makes, we can install, repair, and warranty the work.

Signs You Need a Pro Right Now

• Granules in the gutter. Asphalt shingles shed their protective granules as they age, and finding piles of them at the bottom of your downspouts means your shingles are losing their armor. In Fort Worth, where hail accelerates that process, granule loss is the earliest warning sign of a roof heading toward replacement.
• Water stains on the ceiling. A brown ring on your ceiling rarely shows up the day a leak starts; it usually means water has been working its way through insulation for weeks. If you see one after a rain, the leak is already established, and waiting just spreads the damage into drywall and framing.
• Shingles curling or lifting. On a Fort Worth roof, shingles that cup at the edges or lift in the wind have lost their seal, which means the next hail or microburst can peel them right off. Once that seal dies, the shingle is no longer protecting the decking underneath.
• Daylight in the attic. If you can see sunlight coming through your roof boards from inside the attic, water can get in the same way. That’s a sign your decking is compromised and the roof needs professional attention before one more storm comes through Tarrant County.
• Sagging roof line. A dip or ripple along the ridge or between rafters means the decking or framing has been taking on water for long enough to lose its strength. That is a structural issue, not a leak issue, and it will not fix itself. If you notice your roof line isn’t straight, call (682) 730-3548 before the next heavy rain.

Our Process, Step by Step

1. 1
   Call and talk to a real person. You call (682) 730-3548 and a live person answers, 24 hours a day. We take your information, schedule a time that works for you, and send you a confirmation with the name of the technician who’s coming.
2. 2
   On-site inspection and measurements. Dylan Pace or one of our background-checked, uniformed technicians shows up at the scheduled time. We measure the roof by hand, inspect the decking, flashing, and ventilation from the top, and photograph every problem area. You get copies of the photos we take.
3. 3
   Written price before any work starts. Within one to two days of the inspection, we send a written line-item quote that includes materials, labor, tear-off, disposal, and any decking replacement we anticipate. The number on that page is the number on the invoice, full stop.
4. 4
   Installation with photo updates. On install day, we document the roof before we start, after the tear-off, after the underlayment goes down, and after the final shingle is nailed. You get those photos whether you’re at home or at work, so you can see the condition of your roof at every stage.
5. 5
   Final walkthrough and digital invoice. When the job is done, we walk the roof with you, give you a photo record of the finished work, and send a digital invoice by text. Your warranty paperwork is included, and our 365-Day Done Right Promise means any covered repair that fails within a year is corrected at no charge.

How Much Does Roof Installation Cost in Fort Worth?

Our Service Area Near Fort Worth

We install roofs across Tarrant County, from central Fort Worth out to Roof Installation in Euless and Roof Installation in Keller, and down through Southlake, Benbrook, Crowley, Azle, Kennedale, Lake Worth, River Oaks, Sansom Park, and Haltom City. Most of those areas are a 20 to 35 minute drive from our Fort Worth location, and we schedule installs in one-day or two-day windows so you’re not living under a torn-off roof longer than necessary. If you’re a Fort Worth homeowner, head back to our home page to see everything we handle.

Frequently Asked Questions About Roof Installation in Fort Worth

Schedule Your Roof Installation Service in Fort Worth Today

Call (682) 730-3548 and a real person answers, day or night. We will schedule your free estimate, send you a written price before any work starts, and show you photos of every stage of your roof installation. No surprises, no phone tag, no number that changes at the door.

Written by Dylan Pace, Owner at Crestview Roofing Co Fort Worth, serving Fort Worth since 2000.